Hydraulic Tools
3810 SE Naef Road • Milwaukie, Oregon 97267-5623
  
Handheld Hydraulic Crimping Tools
home page
  about us
  our brands
  products
  what's new
  reconditioned tools
  support
  site map
  contact us  
   
               
    Crimping connectors with the Stanley Hydraulic Tools CT Series crimpers is quick and easy. They are 5-10 times faster than hand-pumped tools and more than twice as fast as high pressure double acting crimpers.

The CT Crimpers require no booster or intensifier which means they can be operated directly from the hydraulic circuits already installed on your line trucks, or from a dedicated power unit, or from one of the STANLEY® lightweight, portable HP Power Units.

Swivel Design on all models provides 360° continuous rotation of the die head for easy alignment to give higher quality crimps.

1650 Models allow the use of the CT on almost any hydraulic system of at least 1,650 psi (114 bar). An accurate, built in relief valve ensures that at these system pressures and higher, a full die load is achieved preventing over-crimping.
               
 
CT04 SE4 Crimping Tool 		     

CT04 STANLEY® SE4 is a small and lightweight tool ideal for service entrance termination and underground crimping. It accepts 90% of available service entrance connectors and accommodates wires up to 4/0 in (13 mm) diameter. It is compatible with the following tooling and die application:

Anderson, VC6-L, VC6-L-SN, VC6-LU, VFC6-LR, VC6-LR-SN, ND58-OL

Burndy, MD-6-8, MD6R, MD6-6R, MD6-6R-2, MD6-AH48, MD6-6AH48 and
MD6-8AH48

Huskie, CN58,CN58H, CN-258, REC-58 (“W” dies), FND-0, ND-0, ND-BG

Kearney, 0-51 and 0-52, PH-1

For more detailed information, click here. 1650 CT Series Specification Sheet.
           
               
 
CT06 Crimping Tool 		CT06 Anderson uses an Anderson Die-Less head designed for use with Anderson-style connectors. It is Compatible with the following tooling and die application:

Anderson, VC6-FT, VC6-FTV, VC6-FTR, and VC6-FTVR

For more detailed information, click here. 1650 CT Series Specification Sheet.
   
               
 
CT10 Burndy 		  CT10 Burndy accepts standard Burndy U-type dies. It is compatible with the following tooling and die application:

Burndy, Y35, L, H

Alcoa, 12A, 12AC, 12HA, 12HAC and 30A

Anderson, HC-12 and HC-12H

Greenlee, 1985

Huskie, EP410, EP410T, EP430, EP510, EP410HT, RP410H, EP510H, PDY-1220 and PDY-1216

Thomas & Betts, 12 Ton

Teledyne, TPU-12 BH

For more detailed information, click here. 1650 CT Series Specification Sheet.

           
 
CT10 Kearney

CT10 Kearney accepts standard Kearney dies. It is compatible with the following tooling and die application:

Kearney, PH2, WH3

Huskie, EP510K and EP510HK

For more detailed information, click here. 1650 CT Series Specification Sheet.
             
 
CT10 Stanley		     CT10 STANLEY® 1½ in. with its unique C-frame opening of 11/2 inches permits the operator to crimp material up to 750 MCM aluminum or copper cable. The larger opening can eliminate the need for larger, more expensive 15 ton tools when crimping large connectors that don’t require 15 tons of die load. The CT10 STANLEY® accepts standard Burndy U-type dies. It is compatible with the following tooling and die
application:

Burndy, Y35, Y750 BH

Alcoa, 12A, 12AC, 12HA, 12HAC and 30A

Anderson, HC-12 and HC-12H

Greenlee, 1985

Huskie, EP410, EP410T, EP430, EP510,
EP410HT, RP410H, EP510H, PDY-1220 and PDY-1216

Thomas & Betts, 12 Ton

For more detailed information, click here. 1650 CT Series Specification Sheet.

           
               

CT15 Universal		 CT15 Universal head model uses die holders that allow the tool to accommodate either Burndy, Kearney or T&B tooling. It will accept the following dies:

Burndy, Y46, Y35

Kearney, PH2, PH14

For more detailed information, click here. 1650 CT Series Specification Sheet.

         
               
link to the stanley works home page   condition of use
Copyright © The Stanley Works 2003• All Rights Reserved